UK design guidance: Dimensions shown are typical architectural reference values and may vary by manufacturer, project requirements and applicable local building regulations. Always verify requirements for your specific project.
Planning a bathroom from scratch means working through layout, services and a handful of trade-specific requirements before a single pipe run is drawn. This guide walks through that process in order — from choosing a layout type through to the practical considerations (drainage, ventilation, electrical safety, waterproofing and accessibility) that a real project has to satisfy.
| Dimension | Value |
|---|---|
| WC branch pipe gradient 18–90 mm fall per metre — the WC branch specifically (Approved Document H Table 2), not a general figure for every fixture. | 18 mm (0.7 in) |
| Built-out wall depth (wall-hung WC/basin) 200–300 mm. | 200 mm (7.9 in) |
| Electrical Zone 1 height (above bath/shower) | 2250 mm (88.6 in) |
| Wet-room floor membrane upstand (warranty guidance) A standard tray-based shower enclosure typically needs more wall coverage (e.g. NHBC: ~600 mm) — see Waterproofing below. | 150 mm (5.9 in) |
| Entrance door clear opening (England, Category 1 baseline) | 775 mm (30.5 in) |
Choose a layout type
Start with what the room needs to do: a main family bathroom, an ensuite or a secondary shower room. Each has a different typical size and fixture mix — see Bathroom Layout Types for a comparison, and the individual guides for Family Bathroom Design, Ensuite Bathroom Design and Shower Room Design for worked examples.
Check fixture sizes and clearances
Once the layout type is settled, confirm the fixture dimensions and recommended clearances in front of each — see Standard Bathroom Dimensions for WC, basin, bath and shower sizes. The relevant British Standard is BS 6465-2:2017 (Sanitary installations — Space recommendations); it gives space, activity and circulation recommendations and example room/cubicle layouts, not a mandatory minimum room size.
Plan the drainage route first
Soil and waste pipe routing is usually the single biggest real constraint on a bathroom layout — more than floor area alone — because it's the hardest and most disruptive thing to change once fixtures are installed.
- WC position is the most constrained fixture. England and Wales's Approved Document H (Table 2) sets a branch discharge pipe gradient of 18–90 mm per metre specifically for a WC branch (100 mm pipe serving up to 8 WCs, or 75 mm for a single WC) up to 15 m long — beyond that, the branch needs its own ventilating pipe or an air admittance valve. The shortest, most direct route to the soil stack is almost always the easiest to get right.
- Basin, bath and shower waste run to smaller branch pipes (sized to each fixture's own trap — typically 32 mm for a basin, 40–50 mm for a bath or shower) with their own length/gradient limits, set out in Approved Document H's Table 1 rather than the WC figure above — these aren't the same table, so don't reuse the WC's 18–90 mm/m range for other fixtures. Shorter and more direct is simpler regardless.
- Wall-hung WCs and basins need a built-out stud wall (typically 200–300 mm deep) to conceal the cistern and pipework.
Approved Document H is England and Wales's drainage guidance — Wales publishes its own current edition rather than defaulting to England's, and Scotland and Northern Ireland set their own separate drainage standards — so confirm the current document and exact table for the project's actual nation before finalising a drainage layout, not just the figures above.
Ventilation
A bathroom without an openable window needs mechanical extract ventilation under building regulations. As a general design principle, position the extract point as far as practical from the main source of replacement air (usually the door) and as close as practical to the main source of moisture (the shower or bath). Confirm the specific minimum extract rate and control requirements (humidistat, overrun timer, etc.) against the current Building Regulations for the project — these are specified precisely enough that general guidance shouldn't be relied on for compliance.
Electrical safety and lighting
UK wiring regulations (BS 7671, Section 701) divide a bathroom into zones based on proximity to water, each requiring a minimum level of protection against moisture ingress:
- Zone 0 — inside the bath tub or shower tray/basin itself. Minimum IPX7; only fittings specifically designed and rated for this zone are permitted.
- Zone 1 — the space directly above the bath or shower, up to 2.25 m. For a shower without a bath or tray, this zone extends 1.2 m from the centre of the fixed water outlet. Minimum IPX4.
- Zone 2 — extends 0.6 m beyond Zone 1 (to the same height, or up to 3 m if the ceiling is higher). Minimum IPX4, IPX5 recommended where water-jet cleaning is likely.
All circuits in the room — not just sockets, but lighting and any circuit merely passing through Zones 1–2 — require 30 mA RCD additional protection. Socket outlets aren't banned from the whole room: an ordinary socket is specifically prohibited only within 3 m (horizontally) of the Zone 1 boundary; outside that 3 m zone, standard sockets are permitted. A shaver supply unit to BS EN 61558-2-5 is the one exception allowed inside Zone 2 itself, away from direct spray.
Notifiability under Part P (England; Wales has had its own, separate Building Regulations since 2014, so don't assume the English rule applies there) depends on the work, not a blanket rule: a new circuit, a consumer unit replacement, or any addition/alteration to an existing circuit within a special location (broadly, the zoned area) is notifiable — straightforward maintenance, repair or like-for-like replacement, or work entirely outside the zones, generally isn't. A registered competent-person-scheme electrician self-certifies rather than notifying building control directly; anyone else doing notifiable work must notify or have it certified by a registered third party. Scotland uses a separate building-warrant system (no "Part P"), and Northern Ireland has no statutory notification regime of this kind at all — Technical Booklet E is guidance only there. Given how specific and safety-critical these zone/IP requirements are, and how much detail is genuinely involved, this is not a DIY specification exercise from general guidance — use a qualified electrician and confirm the exact zone boundaries and IP ratings against the current BS 7671 text for the actual fittings being installed.
For lighting layout (as distinct from electrical safety), plan for task lighting at the mirror/basin in addition to general room lighting, and consider the mirror height guidance in Standard Bathroom Dimensions when positioning a light fitting above it.
Waterproofing
Any floor or wall likely to be regularly wet needs a waterproof membrane (tanking), not just water-resistant tiles and grout — but how much depends on the type of enclosure. BS 5385 (wall and floor tiling) requires waterproofing in these areas without fixing one specific upstand figure for every case; BS 8204-1 covers screeds. The actual heights used in practice typically come from new-build warranty guidance rather than BS 5385 itself: NHBC, for example, distinguishes a standard shower enclosure with a tray (tiling tanked to around 600 mm, reflecting splash risk over a larger wall area) from a level, wet-room-style floor (membrane turned up at least 150 mm at the floor/wall junction) — see Shower Room Design for the wet-room-floor case specifically. Confirm the exact specification against BS 5385/8204-1 and the project's warranty provider and membrane/drain manufacturer's technical data — don't apply one of these upstand figures to the other enclosure type.
Accessibility
Even where a fully accessible bathroom isn't a specific requirement, planning in a wider door opening, reinforced walls for future grab rails, and a level-access shower keeps the room adaptable later at much lower cost than retrofitting. For context on sourcing a doorway figure: in England, Approved Document M's 775 mm figure is specifically the Category 1 (mandatory baseline) clear opening for a dwelling's principal entrance — internal doors instead follow a table trading door width against approach-corridor width, not one flat number — see Standard Door Sizes for that table and how leaf width relates to clear opening. Specific minimum requirements for an accessible bathroom are set by building regulations and depend on the dwelling type and project — always confirm the current requirement before finalising an accessible bathroom design.
Putting it together — planning order
In practice, these steps aren't fully sequential — drainage and electrical zones constrain where fixtures can go, which feeds back into the layout choice from step 1. A practical order that avoids the most costly rework is: (1) rough out a layout against the room's actual soil stack and supply positions, (2) confirm it against fixture clearances, (3) check the drainage routes are achievable within the applicable gradient/length limits, (4) place electrical zones and lighting around the confirmed fixture positions, (5) specify waterproofing for any wet area, (6) revisit accessibility provision if relevant. Changing the layout after step 3 is usually far cheaper than after step 4 or 5.
Frequently asked questions
What's the single biggest constraint when planning a new bathroom?
Usually the route from the WC to the soil stack — gradient and length limits for branch discharge pipes mean the WC's realistic position is often fixed early, which in turn shapes where everything else in the room fits.
Do I need an extractor fan if the bathroom has a window?
Generally no, if the window can be opened — but this depends on the current Building Regulations for the project. Always confirm the current requirement directly.
Can I fit my own bathroom light or shaver socket?
Whether it's formally notifiable depends on the work and the installer — a new circuit or work on a circuit within the zoned area is notifiable in England (Wales now has its own separate rules), while straightforward maintenance or like-for-like replacement generally isn't. Either way, the zone/IP-rating rules in BS 7671 Section 701 are detailed and safety-critical everywhere in the UK, so use a qualified, registered electrician rather than treating this as a general DIY task.
Should I plan for accessibility even if it's not needed right now?
It's a common recommendation, since retrofitting a wider door, reinforced walls for grab rails, or a level-access shower later is far more disruptive and costly than allowing for them during the original build or renovation.
Sources & references
- BS 6465-2:2017: Sanitary installations — Space recommendations. Code of practice.
- Approved Document H: Drainage and waste disposal (England; Wales publishes its own current edition) — Table 2 covers WC/basin/bidet branches specifically, not bath or shower; Table 1 covers trap sizes for single-appliance branches. Scotland and Northern Ireland set their own separate drainage standards.
- Approved Document M, Volume 1 (England) — the 775 mm figure (para 1.14/Table 1.1) is specifically the Category 1 principal-entrance clear opening; internal doors follow a separate width/approach-route table. Scotland, Wales and Northern Ireland each publish their own, numerically different, equivalents — see Standard Door Sizes.
- BS 7671 (IET Wiring Regulations), Section 701 — bathroom electrical safety zones. Figures here are drawn from IET-affiliated trade guidance summarising the regulation, not the copyrighted standard text itself; consult a qualified electrician and the current BS 7671 for any bathroom electrical work.
- BS 5385 (tiling and waterproofing) and BS 8204-1 (screeds) — wet-room floor construction; the commonly-cited 150 mm/600 mm upstand figures are new-build warranty guidance (NHBC and similar), not BS 5385 clauses.
- This is a general planning workflow, not a substitute for checking the current Building Regulations and British Standards applicable to the project's actual nation.




